Door Repair and Installation Richmond Hill

Richmond Hill · York Region

Door Repair and Installation for Richmond Hill Homes

Door repair and installation in Richmond Hill often ends up in the basement. The town sits on sloping ground, so houses in Oak Ridges, Jefferson and Bayview Hill commonly have a walkout with a sliding or garden door at the back.

I am Sercan and I do the work myself. Those lower doors wear faster than the front, because grit and runoff from the slope end up in the track. Interior doors, closet doors and the entry upstairs can all be part of the same visit. Free quote first, and the price is agreed before I start.

Richmond Hill sits on sloping ground, so a large share of the houses in Oak Ridges, Jefferson and Bayview Hill have walkout basements with a sliding or garden door at the back, sitting at grade. Those doors catch runoff and grit washing down the slope, which packs the sill and grinds the rollers, so they wear out long before the front entry does. Down around the Mill Pond the houses are older and smaller, with settled frames and doors that were hand-trimmed once already.

Get a Free Quote +1 (437) 929-3015

Door Repair and Installation in Richmond Hill

Areas covered

Mill Pond Oak Ridges Lake Wilcox Bayview Hill Richvale North Richvale Jefferson Rouge Woods Crosby Beverley Acres

Booking

Mon – Sat: 8:00 AM – 8:00 PM
Sunday: By appointment

Full guide

Read everything about door Repair and Installation

All work in this area

Handyman services in Richmond Hill

Typical Calls

Door Repair and Installation Jobs in Richmond Hill

Rollers replaced on walkout basement garden doors

Sliding doors cleared of grit from sloped yards

New sweeps fitted on lower level patio doors

Interior doors planed in older Mill Pond homes

Double front entry doors realigned in Bayview Hill

Included

What Door Repair and Installation Covers

Sticking and dragging doors adjusted
Loose hinges reset into solid framing
Strike plates re-cut so latches catch
Pre-hung interior doors installed and cased
Slab doors mortised, bored and hung
Bifold and sliding closet doors repaired
Patio door rollers replaced and adjusted
Weather stripping, sweeps and thresholds fitted
Doors undercut for new flooring

Full door Repair and Installation guide

How It Runs

From Message to Finished Job

1

Read the reveal

I look at the gap around the door before touching anything. Where it is tight, where it is wide, and how the latch meets the strike tells me whether the trouble is the hinges, the jamb, the floor or the door itself.

2

Fix the cause

Most doors come right by resetting hinge screws into framing, plugging stripped holes, shimming a hinge leaf or re-cutting the strike plate. Planing stays a last resort, and any bare edge gets sealed once the fit is correct.

3

Hang or replace

Where a door or jamb is past saving, the hinge jamb is set plumb and shimmed behind every hinge, the reveal is checked from top to bottom, and hardware is bored and mortised to fit rather than forced into place.

4

Work the door

The door is swung through its full arc, left at several positions to confirm it stays put, then latched and unlatched repeatedly with the strike adjusted until it catches cleanly without needing a shove.

What Affects the Price in Richmond Hill

Adjusting a door that drags is usually short work, and several doors in the same visit share one setup. Cost rises with an opening that is out of plumb, a sagging or split jamb, hardware that has been repaired badly before, or an exterior door where the threshold and weather stripping also need attention. Fitting a slab into an existing jamb takes longer than hanging a pre-hung unit, because the hinges have to be mortised and the hardware bored. Doors and hardware can be supplied either way, and the price is agreed before work starts.

Nothing starts before the price is agreed. Send a photo or two with your request and I can usually quote without a site visit.

Asked in Richmond Hill

The garden door in my walkout basement sticks after every storm. Why is that?

On the sloped lots in Oak Ridges and Jefferson, water and grit run down toward the walkout and settle in the door track and under the sweep. That debris grinds the rollers and packs the sill so the panel binds. Cleaning the track, fitting new rollers and a fresh sweep usually restores it. If the sill has lifted where the ground settled, that needs shimming rather than new hardware.

Also in Richmond Hill